DMA Consumables & Accessories

The Provectus^™ Balance Controller Unit is a replacement controller for the Provectus Balance System which requires both the balance and controller in order to be fully functional. With this part number, you can order the controller component of this system as a replacement or spare part. Qty. 1

The Provectus^™ Balance Module is a replacement balance for the Provectus Balance system which requires both the balance and a controller unit in order to be fully functional. With this part number, you can order the balance component of this system as a replacement or spare part. Qty. 1

The humidity generator enables reliable control of the relative humidity, in the range of 5% to 90%, within the small environmental measuring chamber.  The HGC20 is controlled through the integrated touch screen.

Non-magnetic.

These stainless steel straight forceps are hooked, non-magnetic, and non-serrated.

Required for the expansion, penetration, compression and flexure modes of operation. Used with high temperature furnace, part of Quartz Parallel Plate System Kit (Product Number: N5390138)

The Flat Tip Penetration Probe is a 1 mm in diameter flat tip that can be used on both the Large and Small Quartz Parallel Plate measuring systems. This probe ships with the TMA 4000 Analysis Kit, but it can also be ordered separately as a replacement or spare.

PerkinElmer's quartz probes are manufactured to extremely high tolerances to ensure the most accurate analysis data from your instrument.

The Flexure Probe is a component of the Flexure TMA Analysis Kit (N5190399), . This probe is a three-point bending probe. It is made of quartz and has a 3 mm knife edge.

The Tare Weight Set consists of 12 stainless steel, flat body weights, ranging from 1 to 500 mg. Each weight is labeled with its weight value. Weight values meet ASTM 6 Class tolerances. This set also includes a set of forceps. This set can be ordered separately using this part number.

Filter Dryer Kit removes moisture and particulates from your purge gas. Includes all the necessary fittings needed to make pneumatic connections easy

The Standard Stirrup Kit includes two matched stirrups consisting of a hook, stirrup ring, and frame designed to support a sample pan sitting inside the stirrup ring. These stirrups are used with the Provectus 6500 Ultramicrobalance and ship with the Provectus 6500 Installation Kit.

The Quick Press Spacer Die is a spool-like, stainless steel rod, approximately 7/8 in high with a diameter of 0.875 in. It is a component of the Quick Press and is used to seal large volume stainless steel capsule. Qty. 1

The Polymethyl Methacrylate (PMMA) Test Sample is a standard calibration material for the DMA analyzers. With this part number, it can be purchased individually as a replacement or spare test. Qty. 5

This replacement Crimper Head is a replacement part for the Standard Sample Pan Crimper Press (02190048). With this part number, you can purchase a crimper head as a replacement or spare.

Included in the Large Volume Stainless Steel Capsule Kit (P/N 03190021).

This tube differs from the standard sample tube in that the 10mm bending platform is permanently fused to the base of the sample tube. Used with the high temperature furnace.

PerkinElmer's quartz probes are manufactured to extremely high tolerances to ensure you obtain the most accurate data from your instrument.

The Tablet Fixed Plate is a component of the DMA 8000 Table Clamp System. This titanium plate is 22 (L) x 14 (W) x 4 (H) mm. One side is V-grooved and the other side has a round groove to allow a wide range of specimens to be held.

The Tablet Fixed Plate is a component of the DMA 8000 Table Clamp System. This titanium plate is 41 (L) x 23 (W) x 6 (H) mm. One side is V-grooved and the other side has a round groove to allow a wide range of specimens to be held.

This kit includes Quick Press (09908467), Quick Press Spacer Die (03191047), 1 pair of guard Ring Inserts (03190236), and 20 of each Pan, Cover and O-Ring (03190218). Pans can withstand an internal pressure of 24 bar, which allows water samples to be heated higher than 100 °C. Each pan has an operating range of -40 °C to 300 °C, unless otherwise limited by the sample vapor pressure.